TECHNICAL  DATA
Type
Ref		 Alloy Finishing Hardness Minimum
Tensile
Strength
(N/mm)		 Minimum
Yield
Strength
(N/mm)		 Minimum
Elongation
AA		 60 Specular
Reflectance		 Total
Reflectance		 Total
Reflectance
TR-2		 Diffuse
Reflectance

Iridescence
1.Controlled
2. Low
 3. Very Low
4. No iridescence
long trans
090 Al. 99.85 specular
standard		 H 18 125 105 2 81 80 86 86 15 1
100 Al. 99.85 specular
brillox 1		 H 18 125 105 2 83 82 86 86 12 2
103 Al. 99.85 specular
mirror		 H 18 125 105 2 84 83 86 86 8 3
106 Al. 99.90 specular
reflex		 H 18 125 105 2 85 84 87 87 7 3
106HB Al. 99.90 specular
reflex EV		 H 18 125 105 2 87 87 >90 >90 6 4
130 5005 reflector
diffuse		 H 14 125 105 2 40 12 83 83 78 2
130/3 5005 reflector
diffuse		 H 14 125 105 2 30 10 82 83 80 4
145 5005 semi
specular		 H 26 150 125 3 50 45 84 84 45 3
210 Al. 99.50 stucco O/H 18 65/140 20/120 20/1-2 - - 83 83 82 2
230 Al. 99.85 hammered H 18 125 105 2 - - 85 85 84 2
235 Al. 99.85 hammered
convex		 H 18 125 105 2 - - 85 85 84 2
250 5005 rigato
satinox		 H 14 140 120 1-2 - - - - - 4

All information provided is based on up-to-date values where possible. Values are typical results from 0.4mm metal and are published for guidance only. For more detailed information, please contact our technical sales department. Physical characteristics of the materials are in accordance with E.N. (European Union Standards). All materials listed above can be delivered in various sizes and forms according to customer requirements. 
SPECULAR REFLECTANCE (ISO 7668)
Measurements are made with Dr Lange Refo3 -D reflectometer		 EUROPEAN NORM STANDARDS (EN) FOR ALUMINIUM
ENTE NAZIONALE ITALIANO DI UNIFICAZONE(UNI)
Alloys                                             UNI-EN 573/3/96
Strength Properties                     UNI-EN 485/2/96
Measuring Standards                  UNI-EN 485/4/96
TOTAL REFLECTANCE (DIN 5063)
 Measurements are made using a 50cm Integrating sphere in our San
Giuliano laboratories		 TEST STANDARD FOR ANODIC OXIDATION
Microscopic measurement of Oxide Layer per UNI EN ISO 1463/98
TOTAL REFLECTANCE AT 30degrees (AASTM E 1651)
Measurements are made with the Technidyne TR2 integrating sphere		 IRIDESCENCE CLASSIFICATION
1= Controlled
2= Low
3= Very Low
4= No iridescence
DIFFUSE REFLECTANCE
Measurements are made using our 50 cm Integrating sphere with a specular 
exit port		  
GENERAL TOLERANCE
Gauge tolerance:           +0.03mm to -0.3mm
Width tolerance:          +0.15mm to -0.15mm
Length-cut sheets:        +1mm/m to -1mm/m		  

NOTE
All materials listed above can be delivered in various sizes and forms according to customer requirements.

CONVERSION TABLE (width 1000 mm)

thickness mm 1 metre = Kg 1 Kg = metres
0.3 0.810 1.235
0.4 1.080 0.925
0.5 1.350 0.741
0.6 1.620 0.618
0.7 1.890 0.529
0.8 2.160 0.463
1 2.700 0.370

CONVERSION TABLE (width 1250 mm)

thickness mm 1 metre = Kg 1 Kg = metres
0.3 1.012 0.988
0.4 1.350 0.741
0.5 1.688 0.593
0.6 2.025 0.494
0.7 2.362 0.423
0.8 2.700 0.370
1 3.375 0.296