ELEKTROMAG Plate Magnet is so flexible you can lay the trap for tramp iron almost anywhere!

ELEKTROMAG Permanent Plate Magnet can be installed in any position, in any condition - in hot, cold or wet locations, on vibrating equipment to trap tramp iron from a wide range of dry, wet, solid materials.

ELEKTROMAG Plate Magnet is a powerful, dependable permanent protection of costly machinery and products against tramp iron and fine iron contamination. It is designed for easy installation in ducts, feedtables and housings, and also for suspension over screens, moving conveyors etc.

IDEAL for so many process industries: Grain Feed, Chemicals, Fertilizers, Foundry Sand, Foodstuffs, Plastics, Pesticides, Minerals, Textile fibers, Wood chips, Clay- products or whatever iron can contaminate!

WHERE TO INCORPORATE ELEKTROMAG PLATE MAGNET

Below material flow: For maximum efficiency magnet is placed beneath rather than above because iron settles down due to force of gravity

Where material is thin: Fix magnet at a location where material thins out so that magnet face will be in close proximity to iron

Where material is slow moving: In chute, or spout, keep the magnet angle below 45 degree and keep magnet near top of chute to permit optimum time for magnetic force to work.

If angle of flow is between 45 degree and 70 degree, Multiple pole magnet is advised

If angle is more than 70 degree or if the flow is vertical use ELEKTROMAG HUMP.

TYPICAL ARRANGEMENTS

ELEKTROMAG Plate Magnet is easily installed in ducts, spouts, feed trays on belt conveyors or screens and in chutes constructed of any type of steel or other material

SELECTION CHART

Chute Bottom Installation
(Material Speeds Upto 61 Meters Per Min.*)

MAXIMUM DEPTH OF MATERIAL (IN MM.)	65	75	100	125
FREE FLOWING, DRY, LOOSE, GRANULAR	PP 1	PP 2	PP 3	ELEK PLATE
MOIST, FIBROUS	PP 2	PP 3	ELEK PLATE	SEE NOTE
DENSE, WET, VISCOUS, LIQUID	PP 3 OR ELEK PLATE	ELEK PLATE	SEE NOTE	SEE NOTE

Above Chutes And Conveyors
Horizontal Suspension
(Material Speeds Upto 61 Meters Per Min.*)

MAXIMUM HEIGHT OF SUSPENSION (IN MM.)	40	50	75	90
FREE FLOWING, DRY, LOOSE, GRANULAR	PP 1	PP 2	PP 3	ELEK PLATE
MOIST, FIBROUS	PP 2	PP 3	ELEK PLATE	SEE NOTE
DENSE, WET, VISCOUS, LIQUID	PP 3 OR ELEK PLATE	ELEK PLATE	SEE NOTE	SEE NOTE

*If speed is between 61 and 99 MP Min, Use 4 pole Magnet
If between 99 and 137 MP Min, Use 6 pole Magnet.

NOTE : Plate Magnet not recommended.
Consult ELEKTROMAG for suitable alternative.

FOR EXTRACTION OF FINE IRON CONTAMINATION FROM DRY FREE-FOLLOWING MATERIALS SUCH AS CEREALS, CHEMICALS, FOOD-STUFFS, SMALL COAL, PLASTIC GRANULES ETC.
FOR THE TREATMENT OF POWDERS CONTAINING SMALL PERCENTAGES OF FINE FERROUS CONTAMINATION.
ELEKTROMAG Permanent Magnetic Chutes have been specially designed to give extremely efficient separation in the above applications. A special feature of this type of magnetic separator is that the magnetic impurities actually come into direct contact with the raw edges of the magnetic poles.

The Chute Type Separators are of all-metal construction with non-ferrous metal sides.

The capacity depends on several factors such as chute width, flow rate and material characteristics. The efficiency of separation depends upon the number of magnetic poles.

Chute type separators are available in standard width, of 200 mm 300 mm and 400 mm and 4 pole units are generally used. Wider units for higher capacities and a larger number of poles for higher efficiencies can also be offered.

Standard stationary chutes are supplied without hoppers or with hoppers as required. Where material does not flow easily on the chute, mechanical agitation by means of vibrating action can be provided. Where precise steplessly-controlled feed is required, the chute can be provided with electromagnetic vibrating feeders.

Totally enclosed dust proof designs are also available. Chutes can also be provided with totally enclosed patterns and flanged inlet and outlet for connection to trunking.

Other designs to suit customers specifications can also be offered.

ELEKTROMAG Permanent Magnetic Humps are used where the flow of material is vertical through ducts and pipes and where material is conveyed along horizontal pneumatic lines.

The unit incorporates two permanent magnetic plates positioned so that tramp iron contained in the flow of material is directed towards the poles of both the magnetic plates ensuring maximum magnetic extraction. The tramp iron pieces usually have a greater density than the feed material and hence increases the tendency for them to move towards the magnet.

The two permanent magnetic plates are hinged type and can be easily opened for manual cleaning.

TECHNICAL DATA